16. You install the Routing and Remote Access service on a Windows 2000 Server computer in your network. Your network is not directly connected to the Internet and uses the private IP address range 192.168.0.0. When you use Routing and Remote Access to dial into the server, your computer connects successfully, but you are unable to access any resources. When you try to ping servers by using their IP addresses, you receive the following message: “Request timed out.” When you run the ipconfig command, it shows that your dial-up connection has been given the IP address 169.254.75.182. What should you do to resolve the problem?
A. Configure the remote access server with the address of a DHCP server
B. Authorize the remote access server to receive multiple addresses from a DHCP server
C. Configure the remote access server to act as a DHCP Relay Agent
D. Ensure that the remote access server is able to connect to a DHCP server that has a scope for its subnet
E. None of above
17. You configure your Windows 2000 Server as a print server. You install a second PnP Network adapter to improve the performance. The first adapter uses IRQ11, and the second adapter uses IRQ5. The server is now unable to print devices connected to a non-PnP LPT2 port adapter. You want to continue to use the print devices connected to your print server. What should you do?
A. Use device manager to change the IRQ for LPT1 to IRQ10
B. Use device manager to change the IRQ for LPT2 to IRQ7
C. Edit the CMOS setting of the servers BIOS to reserve IRQ7 for non-PnP devices
D. Edit the CMOS setting of the servers BIOS to reserve IRQ5 for non-PnP devices
E. None of above
18. Your computer has a mirrored volume and you wish to now install the Recovery Console for future troubleshooting. How do you do this?
A. Reinstall Windows, this can only be applied during the installation
B. Break the mirror, run X:\i386\winnt32.exe /cmdcons Reestablish the mirror
C. Run X:\i386\winnt32.exe / cmdcons
D. Run the add and remove programs and add the recovery console
E. None of above
19. Your Windows 2000 Server computer uses a non-Plug and Play ISA modem configured to use IRQ 5. You add a PCI modem and restart the computer. Device Manager reports an IRQ conflict between the two modems. Both modem are trying to use IRQ 5. You want to resolve the problem. What should you do?
A. Use Device Manager to change the IRQ for the original modem to IRQ 9
B. Use Device Manager to change the IRQ for the original modem to IRQ 10
C. Edit the CMOS settings on the computer to reserve IRQ 5 for non-Plug and Play devices
D. Edit the CMOS settings on the computer to reserve IRQ 10 for non-Plug and Play devices
E. None Of above
20. Your network contains NetWare 4.0 Servers. You have successfully installed Client Service for NetWare on Windows 2000 Professional computers, and Gateway Service for NetWare on Windows 2000 Server Computers. You recently added a new Windows 2000 Server computer to the network and installed Gateway Service for NetWare on it. However, the server is unable to connect to any NetWare servers. What should you do on the new Windows 2000 Server computer to resolve this problem?
A. Enable NWLink NetBIOS
B. Configure the NWLink IPX/SPX/ NetBIOS Compatible Transport Protocol to use the correct Ethernet frame type
C. Install RIP routing for IPX
D. Install the SAP Agent
E. None of above.
Warning: Undefined variable $in_same_cat in /www/wwwroot/mtexam.com/public_html/wp-content/plugins/EXP.GKFEED.COM/function.php on line 27
Warning: Undefined variable $excluded_categories in /www/wwwroot/mtexam.com/public_html/wp-content/plugins/EXP.GKFEED.COM/function.php on line 27